Signal NVR2716 Instrukcja Użytkownika Strona 1

- 1 - USER MANUAL NVR 2708 NVR2716

- 10 - Pic 2.5.2.0 Video playback 1 Playback control 2 Operation hint 3 Record mode 4 Time interval choosing 5 Switch by time,file mode 6 File

- 11 - Special functions：：：： Local zoom:When the system is in single-window full-screen playback mode, you can drag your mouse in the screen to sele

- 12 - Pic 2.5.4 Alarm output 【Configuration】Alarm is on according to the configuration. 【Manual】Click the all button and the according channel is

- 13 - 【Iris】Click / button to adjust the iris of the camera. 【Hide】Current interface will be temporarily hidden after click it.

- 14 - Pic 2.5.5.2 PTZ control 2、、、、Tour Multiple preset points connected tour ,the PTZ run around on the line 1）Tour Settings

- 15 - 3、、、、Scan PTZ also can work on the preset scan line repeatedly. 。 1）Scan setup Setting steps: Step1: I

- 16 - reverse direction to the right scan. When the left and right scan not in the same horizontal ,the PTZ will regard the end of horizontal line

- 17 - 【Direct Aux open】 choose auxiliary equipment, select Open or Close button, switch control； 【 Aux Num open 】 The operation of correspondin

- 18 - 【logout】Quit the menu. Offer password next entrance. 【shut down】Quit the system. Turn off the power supply. When press the shut down button

- 19 - make sure that there are two hard disks installed. One is read-write disk and the other is redundant disk. (refer to 3.5.1) 【Length】Set the

- 2 - Thank you for purchase our product. Please read this user manual carefully to ensure that you can use the device correctly and safely Impor

- 20 - Picture 3.1.3 detect storage device 【Detect】Detect the storage connected with the NVR such as hard disk or universal disk. 【Bac

- 21 - Note：During backup you can exit the page layout to carry out other functions. 【Burning】the file will be burned synchronously after

- 22 - Pic 3.2.1.1 set the time section 【Interval】Only one alarm signal is turned on even there are several motion detect signals in the set interval

- 23 - Pic 3.2.1.2 PTZ linkage 【Delay】When alarm is over,recording will last some seconds(10~300sec),then stop. 【Show message】Pop the alarm informatio

- 24 - Pic 3.2.3 Video loss Set method: refer to chapter 3.3.1. Motion detect 3.2.4 Alarm input When the equipment obtains the external alarm signal,

- 25 - Pic 3.2.6 Abnormal handing 【Event Type】 selecting abnormity you want to inspect 【Enable】 Select it to make sur

- 26 - 【Date Separator】Choose list separator of the data format. 【Time Format】Choose time format: 24-hour or 12-hour. 【Language】Support 29 language

- 27 - 3.3.2 Network setup Pic 3.3.2 Network setup 【Net Card】You can choose cable network card or wireless network card. 【DHCP Enable】Obtain

- 28 - Pic 3.3.3.0 Netservice 【PPPoE setup】 Pic 3.3.3.1 PPPOE Enable：Reverse means choose,setting can become effective. Input the user name an

- 29 - Enable：Reverse mean choose，setting can become effective. Host computer IP:Input the IP address installed NTP server. Port:Default: 123. You c

- 3 - CONTENT CONTENT ...

- 30 - Pic 3.3.3.4 IP filter setup 【DDNS】 Pic 3.3.3.5 DDNS setup It is the abbreviation of dynamic domain name server. Local domain name：Pro

- 31 - Pic 3.3.3.6 FTP setup 【Enable】Click Enable,then all settings will be available 【Server IP】IP address for FTP server 【Port】Domain Port of FTP,d

- 32 - 【Enable】 means it is chosen 【Sever IP】IP address of DDNS server 【Port】: Port No. of device, related DDNS server lis

- 33 - Pic 3.3.3.9 Wireless setup 【Enable】Choose Enable to make all settings available 【Type】Dial type,default AUTO 【Wireless AP】3G access point 【

- 34 - Pic 3.3.3.11 UPNP setup 【Enable】Choose Enable to make sure all UPNP settings available 【HTTP】Route will automatically distribute HTTP port for

- 35 - 【Password】：wireless network password of router； 【IP address】: to set the IP address of device, default is 192.168.1.12 【subnet mask】:set subnet

- 36 - Pic 3.3.4 GUI display 【Time Display】Display the system data and time in the surveillance window. 【Channel title】Display the syst

- 37 - 【Data bits】including 5-8 options，default is 8； 【Stop bits】including 2 options, default is 1； 【Parity】Include odd check, even check, sign check,

- 38 - Pic 3.3.7 tour setup 【Interval】Set the tour switch interval time. The range is 5-120 seconds. 【Alarm tour】set the interval time to shift alarm

- 39 - Pic 3.3.8.1 Single link page of digital channel Multi-linkage page of Digital channel Pic 3.3.8.2 digital channel interface 【C

- 4 - 1 Open-package check and cable connections 1.1 Open-package check When you receive the NVR, please check first. First, please check whether

- 40 - Pic 3.3.8.3 remote channel configure page 【Configure Name】device is with default configure name, user can revise it if necessary； 【Device Type

- 41 - Pic 3.3.8.4 the device list searched under remote channel setting Channel Status: Channel status is to show the status of all the digita

- 42 - Pic 3.3.8.6 Note: when under multi-screen,display extra stream’s resol

- 43 - 3.4 Advanced Manage tools menu including: HDD Manage,Account,Online User, Output Adjust, Auto Maintain, Restore,Upgrade,Device Info,Imp

- 44 - Pic 3.4.2.0 Account 【Modify User】Modify the existed user attribute. 【Modify Group】Modify the existed team attribute. 【Modify Password】Modi

- 45 - Pic 3.4.2.2 add user 【Add Group】Add a user group and set the purview. There are 33 different purviews: shut down the equipment, real time surv

- 46 - 3.4.3 Online user To check the information of network user that connected with local device, also can tick the selected user to break up connec

- 47 - Pic 3.4.6 restore 3.4.7 Upgrade Pic 3.4.7 upgrade 【Upgrade】】】】choose USB interface. 【【【【Upgrade file】】】】choose the upgrade file. 3.4.8 De

- 48 - import related configure file from flash stick to settings, which greatly bring convenience to the customers. Pic 3.4.9 import/export interfac

- 49 - 3.5.2 BPS Display the code stream（Kb/S）and hard disk capability （MB/H）in real time. It displays as the wave sketch map. Pic 3.5.2 BPS 3.5.3

- 5 - press buttons 0~9 to input passwords and user IDs; during playback, press the following: 5) : Increase reverse playback speed 1X, 2X, 4X 6) : Pr

- 50 - Pic 3.5.4 version info Appendix 1.Remote controller operation The remote control is the secondary input device For navigating the

- 51 - 10. MENU: Opens the main menu. 11. EXIT: Close menu windows 12. EXTRA: For the future use. 13. Navigation/Enter: • : Move cursor in menus up;

- 6 - 2.1 Turn on Plug the power supply and turn on the power supply switch. Power supply indicator light shining indicates turning on the v

- 7 - Picture 2.3 System Login Password protection: If the password is continuous wrong three times, the alarm will start. If the password is continu

- 8 - Pic 2.4.1 Preview interface (1) Channel name and status display,click “channel” can pack up (2) Screen switch (3) Full screen display (4) on

- 9 - 2.5.1 Main menu When you login, the system main menu is shown as below. Pic 2.5.1 Main menu 2.5.2 Playback There are two methods for you to p